A load-board-native TMS→
ULTRASHIP LOGOIn collaboration
with
Free LTL tool

Freight class calculator for LTL shipments

Density and NMFC freight class for every pallet and the whole shipment, on the current 13-tier scale. Plus what it takes to drop a class and the linear feet it needs.

  • 2025 NMFC 13-tier scale
  • Class for every pallet
  • No signup

Your shipment

Start from
Line 1Class 100 · 8.44 PCF
Weight is
Line 2Class 175 · 5.50 PCF
Weight is

Measure at the longest points with the pallet, wrap and any overhang included. Numbers stay in this browser.

Shipment class · total weight ÷ total cube

1257.64 PCF

Density 6 to less than 8 lb per cubic foot

Class by handling unit

  • 2 × 48 × 40 × 48 in8.44 PCF100
  • 1 × 48 × 40 × 36 in5.50 PCF175
Handling units
3
Total cube
146.7 cu ft
Total weight
1,120 lb
Linear feet (est.)
8.0 ft

Your pallets fall in different classes. Rated pallet by pallet, the highest is class 175; rated on total weight and cube, the shipment is class 125. Put each unit's weight and dimensions on the bill of lading.

Density-based class on the NMFC scale effective July 19, 2025. Some commodities keep their own NMFC item class, so confirm the item before you book.

Built for the current NMFC rules, not just one pallet

Most free freight class calculators take one set of dimensions and return one number. Here is what this one adds before the bill of lading goes out.

Density scale The 13-tier NMFC scale in force since July 19, 2025Often an older 18-class chart, or no scale named
Pallets on one shipment Up to 30 lines, each with its own size and weightUsually one piece, or one size times a quantity
Class per handling unit Every pallet's class next to the shipment totalOne number for the whole shipment
Dropping a class The cube to cut, the weight to add, the pallet heightGeneral packing tips at best
Linear feet Estimated trailer footprint, stackable lines includedRarely shown
Units Inches and pounds, or centimeters and kilogramsOften inches and pounds only
Keep and share Copy a BOL-ready summary, share a link, printRarely

Freight class chart: the NMFC density scale

The 13 density subprovisions used for density-based classes since July 19, 2025. Your shipment's tier is highlighted.

SubDensity (lb per cu ft)Class
1Less than 1400
21 to less than 2300
32 to less than 4250
44 to less than 6175
56 to less than 8125
68 to less than 10100
710 to less than 1292.5
812 to less than 1585
915 to less than 22.570
1022.5 to less than 3065
1130 to less than 3560
1235 to less than 5055
1350 or more50

How to calculate freight class and density

  1. Measure every handling unit

    Length, width and height at the longest points, with the pallet and packaging included. Pick a common pallet size to fill in length and width.

  2. Enter the weight

    Per unit or for the whole line. Add a line for each different size, mark lines that can stack, and switch to centimeters and kilograms if you need to.

  3. Read the class and the next step

    You get density and class for every handling unit and for the whole shipment, what it takes to drop a class, and the linear feet on the trailer floor.

Freight class questions

Measure each handling unit at its longest points, including the pallet and packaging, and weigh it. Multiply length by width by height in inches and divide by 1,728 to get cubic feet. Divide the weight in pounds by the cubic feet to get density in pounds per cubic foot (PCF). Then find that density on the NMFC density scale: for example, 8 to less than 10 PCF is class 100.

It depends on the height and the weight. A 48 x 40 x 48 in pallet is 53.3 cubic feet. At 450 lb that is 8.44 PCF, which is class 100. The same pallet at 300 lb is 5.63 PCF, which is class 175. Shorter or heavier pallets are denser and land in a lower class.

On July 19, 2025 NMFC Docket 2025-1 moved thousands of commodities to density-based classes and expanded the density scale from 11 to 13 subprovisions, adding classes 50 and 55 for very dense freight. The scale now runs from class 50 at 50 PCF or more to class 400 below 1 PCF. This calculator uses that scale.

NMFTA keeps updating the classification. Docket 2026-1 took effect on May 23, 2026, and Docket 2026-2, published for comment on August 28, 2026, proposes a rewrite of the mixed-freight rule (Item 640) that leans further on density figured for each handling unit. That is why this calculator shows the class of every handling unit as well as the shipment total.

Not always. Most commodities are now classed by density, but some NMFC items still carry a specific class because of handling, stowability or liability. Treat this result as the density-based class and confirm the NMFC item for your commodity, for example in NMFTA's ClassIT, before you book.

Yes. Carriers measure and weigh the whole handling unit as it is tendered, so include the pallet, crate, wrap and any overhang. Measuring the product alone is one of the most common reasons freight gets reclassed.

Linear feet is the length of trailer floor the freight takes up. A dry van is roughly 98 inches wide inside, so 48 x 40 pallets usually load two across, and each pair uses 4 feet of floor. Stacking units cuts the floor space. This calculator estimates linear feet from your units, sizes and the stackable setting; the carrier's own load plan decides the final figure.

When the dimensions or weight on the bill of lading don't match what the carrier's dimensioner and scale record, the carrier corrects the class and bills the difference, often with an inspection fee. Accurate measurements for every handling unit are the simplest way to avoid it.

Density decides the class, so either the weight goes up or the cube comes down. Tighter packing, a lower pallet height or combining pieces onto fewer pallets reduces cubic feet. The result shows how much the cube would need to shrink, or the weight rise, to reach the next lower class.

For freight brokers and 3PLs

Quote, book and bill LTL in one place

UltraShip is the TMS purpose-built for non-asset freight brokers. LTL quoting, booking and billing sit in the same system as your carriers, loads and accounting, so the class on the quote follows the load all the way to the invoice.